Issue: No connection RAK2013 Pi3+
Setup: Pi3+ RAK2013
Details:
Hi Folks,
I am new here and this thread looks similar to my needs. I have a RAK2013 Raspberry Pi Hat that incorporates the BG96. I am Australia and using a Telstra SIM card. I am new to Raspberry Pi so my issue may be more towards the Pi and not the BG96. looking at the above thread I have entered all the AT commands as directed and every looks good to me however I cannot get a cellular connection on my Pi3+. With the USB connected to the Pi and the USB micro connected to the Hat I get the connection notification on my panel with a wwan0 displaying an IP address however there is no internet connection. If I remove the USB cable I get no connection. I want to be able to run this Hat without a cable due to space limitations.
Any suggestions would be most apricated.
at+cereg?;+cgreg?;+cops?;+qcsq;+qnwinfo
+CEREG: 0,1
+CGREG: 0,4
+COPS: 1,0,“Telstra #StaySafe Telstra”,8
+QCSQ: “CAT-M1”,-65,-95,139,-13
+QNWINFO: “CAT-M1”,“50501”,“LTE BAND 28”,9410
OK
pi@raspberrypi:~ $ sudo minicom -D/dev/ttyAMA0 -b 115200
Welcome to minicom 2.7.1
OPTIONS: I18n
Compiled on Aug 13 2017, 15:25:34.
Port /dev/ttyAMA0, 17:28:31
Press CTRL-A Z for help on special keys
at+cgdcont?
+CGDCONT: 1,“IP”,“Telstra.Internet”,“0.0.0.0”,0,0,0,0
OK
at+cgcontrdp
+CGCONTRDP: 1,5,Telstra.Internet,10.90.138.139,10.5.133.45,10.4.27.70
OK
at+cops?
ERROR
AT+COPS?
+COPS: 1,0,“Telstra #StaySafe Telstra”,8
OK
AT+CIMI
505013532673850
OK
AT+QCSQ
+QCSQ: “CAT-M1”,-66,-98,138,-13
OK
AT+QMBNCFG=“LIST”
+QMBNCFG: “List”,0,0,0,“Att_Non_Volte_Lab”,0x05010310,201712191
+QMBNCFG: “List”,1,0,0,“China_Common”,0x05802800,201806231
+QMBNCFG: “List”,2,0,0,“Telstra-Commercial”,0x05801801,201806301
+QMBNCFG: “List”,3,0,0,“ROW_Commercial”,0x05800801,201806301
+QMBNCFG: “List”,4,0,0,“Verizon_Commercial”,0x05803801,201806301
OK
AT+QCFG=?
+QCFG: “nwscanmode”,(0,1,3),(0,1)
+QCFG: “nwscanseq”,(00-010203),(0,1)
+QCFG: “servicedomain”,(1,2),(0,1)
+QCFG: “roamservice”,(1,2,255),(0,1)
+QCFG: “band”,(0-F),(0-7FFFFFFFFFFFFFFF),(0-7FFFFFFFFFFFFFFF),(0,1)
+QCFG: “msc”,(0-2)
+QCFG: “sgsn”,(0-2)
+QCFG: “celevel”,(0-2)
+QCFG: “pdp/duplicatechk”,(0,1)
+QCFG: “iotopmode”,(0-2)
+QCFG: “nb1/bandprior”,<band_priority_seq>
+QCFG: “psm/urc”,(0,1)
+QCFG: “ledmode”,(0,1,3)
+QCFG:: “gpio”,(1-3),[,[,,]/[][,]]
+QCFG: “airplanecontrol”,(0,1)
+QCFG: “urc/ri/ring”,(“off”,“pulse”,“always”,“auto”,“wave”),(1-2000),(1-10000),)
+QCFG: “urc/ri/smsincoming”,(“off”,“pulse”,“always”),(1-2000),(1-5)
+QCFG: “urc/ri/other”,(“off”,“pulse”),(1-2000),(1-5)
+QCFG: “risignaltype”,(“respective”,“physical”)
+QCFG: “urc/delay”,(0,1)
+QCFG: “cmux/urcport”,(0-4)
+QCFG: “ims”,(0-2)
+QCFG: “apready”,(0,1),(0,1),(100-3000)
+QCFG: “nccconf”,(0-1FF)
+QCFG: “psm/enter”,(0,1)
+QCFG: “apn/display”,(0,1)
+QCFG: “snrscan”,(0-2)
OK